100% Free · No Upload · Runs in Your Browser

Repair STL files online — free, in your browser

Fill holes, fix non-manifold edges, flipped normals and degenerate faces for a watertight, print-ready mesh. The geometry engine runs locally on your device in a Web Worker — the file never leaves this browser.

Drag & drop your .stl file here

or

Not a single network request is made. You can verify it in DevTools → Network — or just turn off Wi-Fi.

No file handy? Try a known-broken sample:

What is STL repair?

An STL file describes a 3D model as a mesh of triangles and is the de-facto format used by almost every 3D printer and slicer. For a part to slice and print correctly, that mesh has to be watertight and manifold — meaning every edge is shared by exactly two triangles, there are no gaps, and the surface has a clear inside and outside.

In practice, many meshes are not. Holes appear when a CAD export drops faces, boolean operations leave non-manifold edges, downloaded models contain flipped normals, and repeated editing can introduce duplicate or degenerate triangles. Slicers respond with failed prints, missing layers, or slicing errors that are hard to trace back to the source.

STL repair is the process of detecting these topological defects and correcting them so the mesh forms a closed, consistent, print-ready surface — without changing the intended shape. This tool runs that whole process locally and reports each defect with a real count instead of a vague "fixed" message.

Common STL file problems and how to fix them

The diagnosis report detects the following issues. Each is described below, including why it breaks a print and how it is corrected.

Holes & boundary loops Error

A hole is an opening where edges are attached to only one triangle, leaving the surface unsealed. A slicer cannot tell what is inside and may drop the surrounding region.

Fix: boundary loops are detected and closed by adding the minimal number of triangles needed to fill the gap.

Non-manifold geometry Error

Edges shared by more than two triangles, or vertices where several surfaces meet in an ambiguous way, make a mesh mathematically invalid and unpredictable to slice.

Fix: offending vertices are split and duplicated edges separated so every edge belongs to exactly two triangles.

Flipped & inconsistent normals Warning

Normals define which side of a face points outward. Inconsistent winding confuses slicers and can cause inverted or hollow-looking prints.

Fix: face orientation is unified and flipped normals are corrected consistently across the mesh.

Degenerate & duplicate faces Warning

Zero-area triangles and overlapping faces add no geometry but break topology and inflate face counts, sometimes halting the slicer.

Fix: degenerate and duplicate faces are removed while leaving the real surface intact.

Unwelded duplicate vertices Warning

Separate vertices that occupy the same point keep adjacent faces disconnected, producing invisible seams and open edges.

Fix: coincident vertices are welded within a small tolerance so neighboring faces connect.

Self-intersecting surfaces Error

When triangles pass through each other, the volume is ambiguous and the print may contain internal overlaps. This is among the hardest defects to resolve safely.

This version: a strict validator flags self-intersection honestly rather than pretending it is fixed, so you can decide how to handle it.

How the online STL repair tool works

  1. 1

    Drop your STL

    Drag & drop or browse. The file is read locally and never transmitted.

  2. 2

    Review the diagnosis

    Get a structured report of holes, non-manifold geometry and topology with real counts — not a vague "fixed".

  3. 3

    Repair & download

    One click repairs what can be fixed, then a strict independent check verifies the result before you export.

Why our STL repair preserves your geometry

Your shape is preserved

Normal fixes and degenerate removal change no geometry. Hole filling adds only the minimal faces needed to close a gap.

Preview before you export

Inspect before and after from the same camera angle, with exact vertex and face counts.

Honest about limits

If self-intersecting geometry can't be guaranteed, the strict validator says so instead of pretending it worked.

The STL repair pipeline, step by step

Repair runs as an ordered sequence of conservative operations. Each step addresses a specific defect and the result is then checked by an independent validator.

1

Weld duplicate vertices

Coincident points within a tolerance are merged so adjacent faces connect and invisible seams close.

2

Split non-manifold vertices

Ambiguous junctions are separated into well-defined surfaces so every edge belongs to exactly two triangles.

3

Fill holes

Boundary loops are closed with the minimum new faces, preserving the surrounding geometry.

4

Remove degenerate & duplicate faces

Zero-area and redundant triangles are stripped without altering the intended shape.

5

Fix normals

Face winding is unified so the surface has a consistent outward orientation.

How to check if an STL is watertight and print-ready

The report uses these topological measures. They are explained here so you can read the diagnosis rather than trust a green checkmark.

MeasureWhat it means
ManifoldEvery edge is shared by exactly two triangles and every junction is well-defined. A non-manifold mesh is invalid for printing.
WatertightThe surface has no boundary edges or holes, so it fully encloses a volume with a clear inside and outside.
GenusThe number of independent through-holes topologically. A simply closed solid reports genus 0; a higher value reflects intentional tunnels rather than defects.
Euler characteristicA relationship between vertices, edges and faces used to verify the consistency of the topology.
Boundary loopsChains of single-sided edges that outline open holes. A print-ready mesh has zero boundary loops.
Connected componentsThe number of separate solid pieces. Multiple components are valid for assemblies but each should itself be manifold.

When to use an STL repair tool

Models downloaded from repositories

Files from STL libraries and community sites can arrive with open edges or flipped normals and need a quick fix before slicing.

After CAD or boolean modeling

Exports and boolean cuts frequently leave non-manifold edges or tiny gaps that only surface at slicing time.

Confidential and in-house designs

Pre-release product geometry can be repaired without uploading it to a third-party server, keeping it on the device.

Large and high-poly meshes

Because files are not uploaded, even large models are processed on the device without waiting for an upload or queue.

STL repair FAQ

How does this work without uploading my file?

The repair engine is compiled to WebAssembly and runs in a Web Worker inside your browser. Your mesh is processed on your device and never sent over the network — it even works offline.

What issues can it repair?

It welds duplicate vertices, splits non-manifold vertices, fills holes, removes degenerate and duplicate faces, and corrects flipped normals — the common causes of 3D print failures.

Will repairing change the shape of my model?

Repairs are kept as conservative as possible. Most operations don't touch geometry at all; hole filling adds minimal new faces. You can preview every change before exporting.

Is there a file size or usage limit?

There is no account and no repair count limit. File size is bounded only by your browser's memory rather than an upload cap, since nothing is uploaded.

What happens if a file can't be fully repaired?

A strict independent validator checks the result and tells you plainly if a problem such as self-intersection remains, so you can decide how to handle it rather than printing a bad file.

What input and output formats are supported?

The tool reads binary and ASCII STL files and exports a repaired STL. The underlying engine also supports OBJ, OFF and PLY, which can be exposed as the toolset expands.

Does it work on mobile and without internet?

Yes. It runs in any modern browser on desktop or mobile, and because the engine is downloaded to your device, the tool keeps working after you disconnect from the internet.

How is this different from rebuilding the model?

Repair only corrects topological defects and adds minimal faces to close holes; it does not redesign or remodel your part. The dimensions and intended geometry are preserved, and you can compare exact counts before and after.